
ServicesWindow Installation
Window Installation in Carson
We install windows where there wasn't one before, or where the whole old frame has to come out. We open up the wall, look at what's really there, and tell you plainly what it needs. Then we set the window square, flash it and seal it.
When installation is the right job
Window installation is different from swapping glass in an old frame. It covers new openings, enlarged openings, room additions, garage conversions and any spot where the old frame is too damaged to keep. The window goes in with a nail fin or full frame, tied into the wall and the weather barrier behind the stucco.
If your existing frames are sound and you just want better windows, our Window Retrofitting or Window Replacement work may cost less and disturb less. We look first and tell you which one fits. We don't push the bigger job when the smaller one will do.
Most homes around Carson have stucco walls, so a new opening means cutting stucco, framing a header and patching the finish to match. That patch is part of the job, not an afterthought.

What the work includes
- 01
Opening check
Before we cut anything, we check the wall for wiring, plumbing and studs. You see what we found and where the window can go.
- 02
Framing and header
New or wider openings get a proper header sized for the span. The rough opening is built square and level so the window operates right for years.
- 03
Flashing and weather barrier
We lap flashing tape and building paper so water runs out, not in. This step is hidden once the stucco is back, so we take photos for you.
- 04
Setting the window
The window is shimmed, fastened and checked for smooth operation and a tight lock before it is sealed.
- 05
Stucco and interior finish
We patch the stucco around the new frame and finish the inside with drywall returns or trim.
- 06
Permit and cleanup
New and enlarged openings usually need a permit. We pull it, meet the inspector and haul away the debris.
Questions about Window Installation?
Call(310) 340-7107Signs you need a full installation
Rot or cracks in the frame
If the wood frame is soft or the sill is split, an insert would sit on bad wood. The frame needs to come out.
Water stains below the window
Stains on the wall or floor under a window often mean the flashing failed. That gets fixed by opening the wall, not by caulking over it.
A dark room you want to open up
A wider window or a new opening can change how a room feels. We check whether the wall can take it before you decide.
A bedroom without a proper exit
Bedrooms need a window big enough to climb out of. Converted rooms and garages often fall short and need a larger opening.
An addition or ADU going up
New rooms need windows that meet current energy and safety rules. We install them during the build.
How the job runs
- 1
Inspection and findings
We come out, measure and look at the wall inside and out. You get our findings in plain words and a written estimate with each line spelled out.
- 2
Permit and order
If the job needs a permit, we file it. We order windows to the exact opening size so nothing gets forced to fit.
- 3
Install day
We cover floors and furniture, cut the opening, frame it and set the window. The wall gets closed up and weather-tight before we leave.
- 4
Finish and inspection
We patch the stucco, finish the inside and walk you through how the window works. If an inspection is required, we're there for it.
What moves the price
Every opening is a little different, so we price after we see it. Your estimate lists the window, the labor, the framing, the stucco work and the permit as separate lines. We'll beat any estimate from another licensed contractor or USA-made window supplier.
- New opening or existing one
- Cutting a new hole in a wall means a header, framing and more stucco patching. Reusing an opening costs less.
- Size and window type
- Larger units, sliders versus casements, and tempered glass near doors or tubs all change the material cost.
- What we find in the wall
- Rotted framing, old water damage or wiring in the way adds work. We show you before we do it.
- Stucco and finish work
- Matching texture and color on an older wall takes more time than a plain patch.
- Permits and access
- Permit fees, second-story openings and tight side yards all play into the final number.
Window installation questions
What's the difference between installation and retrofitting?
A retrofit sets a new window inside the old frame and leaves the wall alone. Installation takes the frame out or starts with a new opening, so we can fix framing and flashing. Retrofitting is less work when the old frame is sound. We tell you which one your home needs after we look.
Do I need a permit?
New or enlarged openings in an exterior wall usually need a building permit. A same-size swap often doesn't. We check with the building department, pull the permit when it's needed and handle the inspection.
What credentials do you carry for this work?
We hold a CSLB C-17 license, which is the California classification for glazing work. We're also bonded and insured, with $2 million insurance coverage. That matters on a job like this, where part of your wall is open while we work.
Will the new window meet California energy rules?
Yes. New windows have to meet the state's Title 24 energy standards, and the windows we install do. If you want to go further, our Energy Efficient Windows page covers glass options.
How messy is it?
Cutting stucco makes dust, so we cover floors, move furniture and seal off the work area. We clean up at the end of each day and take the debris with us.
Do you work outside Carson?
Yes. We install windows in Torrance, Gardena, Long Beach, Lomita and the other towns nearby.

Let us look at the wall first
We'll come out, check the opening and tell you straight what it needs. Free in-home estimates with no sales pressure or obligation.